Bugs

Check here for the current official version of the Go Fab CNC software
Warrenh
Posts: 80
Joined: Sat May 18, 2019 1:20 pm
Re: Bugs

Post by Warrenh » Fri Feb 07, 2020 12:57 am

Individuals. I had a seahorse with 50 or 60 Pierces. 5 were wrong side. I added nodes to all paths, still wrong side. It's not every file and it is a small amount. It's not critical but it would be a help. The old version did this too so not a new bug.

Warrenh
Posts: 80
Joined: Sat May 18, 2019 1:20 pm
Re: Bugs

Post by Warrenh » Wed Feb 12, 2020 2:17 pm

I found something yesterday. I have monogram file that is an 18 inch circle. It imported perfect and the actual size was correct and it cut correctly but the size shown at the top right was 18 x 24 inches, not 18 x18. It seems the program displayed the size wrong. Everything else was fine including finished cut size

elopez
Posts: 81
Joined: Fri Jan 03, 2020 5:29 pm
Re: Bugs

Post by elopez » Wed Feb 12, 2020 3:23 pm

Warrenh wrote:
Wed Feb 12, 2020 2:17 pm
I found something yesterday. I have monogram file that is an 18 inch circle. It imported perfect and the actual size was correct and it cut correctly but the size shown at the top right was 18 x 24 inches, not 18 x18. It seems the program displayed the size wrong. Everything else was fine including finished cut size
Did you also have another file open at the same time?

If not, could you send me the file so I can look at it?

elopez2192@gmail.com

Warrenh
Posts: 80
Joined: Sat May 18, 2019 1:20 pm
Re: Bugs

Post by Warrenh » Wed Feb 12, 2020 5:26 pm

I didn't and where do I send it

Warrenh
Posts: 80
Joined: Sat May 18, 2019 1:20 pm
Re: Bugs

Post by Warrenh » Wed Feb 12, 2020 5:29 pm

I see it now

elopez
Posts: 81
Joined: Fri Jan 03, 2020 5:29 pm
Re: Bugs

Post by elopez » Wed Feb 12, 2020 8:16 pm

Warrenh wrote:
Wed Feb 12, 2020 5:29 pm
I see it now
Which version of the app are you suing? I'm not seeing the same issue on my end.

Warrenh
Posts: 80
Joined: Sat May 18, 2019 1:20 pm
Re: Bugs

Post by Warrenh » Wed Feb 12, 2020 8:50 pm

The latest 3.17. maybe it was a one time glitch. IDK

Dave56
Posts: 74
Joined: Wed Sep 25, 2019 3:45 am
Location: Central Illinois
Re: Bugs

Post by Dave56 » Fri Feb 14, 2020 8:30 pm

Yes.Thank you for your time and effort into making this file work better....I was wondering if sizes on #`s was fixed..Its been a few weeks since I had new software installed.but went back to old..when I made some #s for a Commercial Barge Company,and they was to be 4 inches tall..after cutting them all out of 1/4"..I didnt think they looked right. measured them..and they was only 3 1/2" tall instead of 4 "..Thanks

Dave56
Posts: 74
Joined: Wed Sep 25, 2019 3:45 am
Location: Central Illinois
Re: Bugs

Post by Dave56 » Sat Feb 15, 2020 8:18 pm

Also yesterday while using new update..While watching my file cut on my tablet..The torch was cutting on the right side of a Rose.but tablet show it was on my left side it was cutting..Its backwards....That is something that will have to fix..I use it alot myself..thanks also let us know you are reading these.thanks

elopez
Posts: 81
Joined: Fri Jan 03, 2020 5:29 pm
Re: Bugs

Post by elopez » Sat Feb 15, 2020 8:30 pm

Dave56 wrote:
Sat Feb 15, 2020 8:18 pm
Also yesterday while using new update..While watching my file cut on my tablet..The torch was cutting on the right side of a Rose.but tablet show it was on my left side it was cutting..Its backwards....That is something that will have to fix..I use it alot myself..thanks also let us know you are reading these.thanks
I'm looking into it. Does that happen on all of your files? Did it cut it incorrectly?


Post Reply