3/4"

Show pictures of projects you've done.
Post Reply
chademling94
Posts: 148
Joined: Sun Aug 19, 2018 6:57 pm
Location: Wisconsin
3/4"

Post by chademling94 » Tue Dec 04, 2018 1:38 am

Pierces didn't go so hot (actually to hot :P ) but edge start worked good! I drilled a hole for the center pierce.
Attachments
Snapchat-365783050.jpg
KROOKED IRON FAB & STEEL
CHAD EMLING
Millermatic 252
Synchrowave 210
Thermal Dynamics Cutmaster 52
Grizzly G0757Z H/V Mill
Grizzly G0765 Lathe
Ellis 1600
Everlast 80s
GoFab CNC 4'x8' Plasma Table

GregSmith
Posts: 53
Joined: Wed Sep 12, 2018 2:44 am
Re: 3/4"

Post by GregSmith » Mon Dec 10, 2018 8:55 am

Nice! Was this on your 80amp Everlast? What amperage and cutting speed?

chademling94
Posts: 148
Joined: Sun Aug 19, 2018 6:57 pm
Location: Wisconsin
Re: 3/4"

Post by chademling94 » Mon Dec 10, 2018 3:28 pm

Yes 80 amp everlast. Cut at 65 amps and 175 feedrate
KROOKED IRON FAB & STEEL
CHAD EMLING
Millermatic 252
Synchrowave 210
Thermal Dynamics Cutmaster 52
Grizzly G0757Z H/V Mill
Grizzly G0765 Lathe
Ellis 1600
Everlast 80s
GoFab CNC 4'x8' Plasma Table

ClifO
Posts: 6
Joined: Wed Nov 28, 2018 4:08 pm
Re: 3/4"

Post by ClifO » Tue Dec 11, 2018 2:12 pm

That's really clean! Can't wait to get mine.

GregSmith
Posts: 53
Joined: Wed Sep 12, 2018 2:44 am
Re: 3/4"

Post by GregSmith » Sat Dec 15, 2018 7:51 pm

I get jitters in 10ga at 50amps 1400mm
16ga jitters at 30amp 750mm and 40a at 1400mm. Having trouble getting clean cuts so can’t do art work until its cleaned up.

chademling94
Posts: 148
Joined: Sun Aug 19, 2018 6:57 pm
Location: Wisconsin
Re: 3/4"

Post by chademling94 » Sat Dec 15, 2018 11:31 pm

The way the torch is clamped is the issue. If you look in the Tips and Tricks section under (Cuts look jagged or sawtooth like) Bdspindles made a fantastic looking clamp which i think is the direction i am going to go. But yes anything over like 400mmpm i get a crazy torch jitter on sudden direction changes.
KROOKED IRON FAB & STEEL
CHAD EMLING
Millermatic 252
Synchrowave 210
Thermal Dynamics Cutmaster 52
Grizzly G0757Z H/V Mill
Grizzly G0765 Lathe
Ellis 1600
Everlast 80s
GoFab CNC 4'x8' Plasma Table

GregSmith
Posts: 53
Joined: Wed Sep 12, 2018 2:44 am
Re: 3/4"

Post by GregSmith » Wed Jan 23, 2019 10:08 am

Wow, I never thought it would be a clamping issue. Looks like I found another project for my cnc mill. Thanks. I’ll post a picture when I get the clamp milked out.


Post Reply