Pre-Release of the next Update!

Check here for FREE Updates to your Go Fab CNC Table
User avatar
Dave
Posts: 203
Joined: Fri Jun 29, 2018 4:39 am
Location: Pflugerville, TX
Contact:
Re: Pre-Release of the next Update!

Post by Dave » Tue Jun 11, 2019 7:36 pm

rdwesley wrote:
Mon Jun 10, 2019 2:21 am
I uninstalled my program and was able to install new version...

Some feedback on issues I came across.

Cutting 14 gauge..

1) My torch now appears to be dragging with the stock settings.
2) doesn’t wait for pierce through sometimes before starting
3) didn’t appear to update the table at all
4) travel height did not work for me
5) tried to pause and was unable to see settings that would allow you to move torch to another segment.
6) when tablet locked and I reopened the program all i saw was program running. Unable to see file cuts etc...
7) mine says table version ? At top of screen.
8) pierce points when cutting out a piece it leads in and when the piece completes, it falls out and torch continues to run and falls down because piece it was cutting is gone.
Thanks for trying out the pre-release, the feedback really helps. I checked out the tattered flag and it's consistent on inside/outside and cut order now but some pierce points still end up on the wrong side. Will look into it.

rdwesley
Posts: 77
Joined: Mon Jul 09, 2018 11:42 pm
Re: Pre-Release of the next Update!

Post by rdwesley » Fri Jun 14, 2019 8:10 pm

Thanks Dave

cnc164
Posts: 28
Joined: Tue Sep 18, 2018 9:42 pm
Location: Ontario Canada
Contact:
Re: Pre-Release of the next Update!

Post by cnc164 » Wed Jun 19, 2019 3:20 pm

Is there a way to set the speed when jogging for a manual cut?

Ryan Lindsey
Posts: 64
Joined: Thu Jun 28, 2018 4:21 am
Re: Pre-Release of the next Update!

Post by Ryan Lindsey » Wed Jun 19, 2019 5:47 pm

No, but that’s a great idea. I’ll find a way to incorporate that.

Have you been using the Manual Cut feature a decent amount?

cnc164
Posts: 28
Joined: Tue Sep 18, 2018 9:42 pm
Location: Ontario Canada
Contact:
Re: Pre-Release of the next Update!

Post by cnc164 » Thu Jun 20, 2019 1:33 pm

No I haven’t . But I definitely will if you can set speed .

I tried the Beta version but reverted back to the October 2018 version .

On my table the beta version did something to the stepper motors that caused a very jerky motion on the large movement, but was smooth on the small movement option?

Also(still running original tablet) I crashed every time I tried to open a .nc file.

Looks promising though!

rdwesley
Posts: 77
Joined: Mon Jul 09, 2018 11:42 pm
Re: Pre-Release of the next Update!

Post by rdwesley » Sun Jun 23, 2019 11:07 pm

I need settings for the update. The parameters changed from metric to standard and I tried converting, but they don’t work. I now have a LOT of slag and burn outs on 14 gauge. Have ruined quite a bit wit trial and error. Can anyone help?

rdwesley
Posts: 77
Joined: Mon Jul 09, 2018 11:42 pm
Re: Pre-Release of the next Update!

Post by rdwesley » Sun Jun 23, 2019 11:25 pm

Also it randomly closes, and when it does it wipes out the file that is loaded. You have to start over.

Randy
Posts: 288
Joined: Thu Jan 24, 2019 1:52 am
Location: OHIO
Re: Pre-Release of the next Update!

Post by Randy » Sun Jun 23, 2019 11:28 pm

I haven't updated due to i can't afford a mess up at this time things booming off my table

rdwesley
Posts: 77
Joined: Mon Jul 09, 2018 11:42 pm
Re: Pre-Release of the next Update!

Post by rdwesley » Sun Jun 23, 2019 11:32 pm

Every time I try to test it is settings it closes program also. And I thought someone said you can manually cut. Where is that option?

rdwesley
Posts: 77
Joined: Mon Jul 09, 2018 11:42 pm
Re: Pre-Release of the next Update!

Post by rdwesley » Mon Jun 24, 2019 1:04 am

How do I revert table back to old program? Too many issues?


Post Reply